How are custom Glock slides machined?
May 07, 2014 · Tennifer refers tonal process to harden the metal. Glock then applies whatever the finish is onto the slide after its been treated. Also, I'm not sure they even use Tennifer any more. That's a brand name. They still treat the metal, but possibly with a generic process instead. Save Reply D DPris Registered Joined Mar 3, 2006 1,163 Posts
How does Glock work?
Jan 01, 2014 · Glock is using nitration on the slide. It has a Rockwell hardness of 68. 70 is as far as the scale goes. Tenifer is 64. In Austria the military shows the troops how to sharpen their knife on the slide. It's that hard. Both Tenifer and Melonite are "brand names" for a nitration process. Not much has really changed.
How hard is the Glock slide?
Feb 04, 2014 · Meloniting, gas nitriding, salt bath carburizing (sp) and Tenifer are all close to the same process and harden the metal. The final cosmetic finish is not from the meloniting. Same reason a Glock can have a ton of holster wear and still not rust. The hardening is still there providing the corrosion resistance.
Does Glock use the Tenifer finish on their slides?
Nov 07, 2016 · Glock slides are machined from bar stock, though I don't recall if it's a custom extrusion or standard stock. I expect it's an extrusion to a near-net size, given their quantities. Having their own mill run would also give them control over initial heat treatments as well.
What coating does Glock use on their slides?
Cerakote Coating for Glock Slide.
How does Glock finish their slides?
In the case of the Glock 19, the original Gen 1 and Gen 2 were finished with a Parkerizing process. Parkerizing is otherwise known as phosphate conversion coating, and its primary purpose is to provide more protection against corrosion and wear. Parkerizing is done on rough surfaces, and its finish is matte.Oct 18, 2015
Are Glock slides heat treated?
The slides are milled from blocks of steel. I am not sure what kind of steel though. The reason they use tennifer rather than actually heat treating them is they want to be able to turn out huge orders extremely fast. Glock has met orders of 50,000 guns in like a month.Aug 31, 2011
Do you oil a Glock slide?
1:396:47How to Lubricate a Glock the RIGHT Way - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd they over lubricate them that's a big reason why Glock pistols are sent back to the factory noteMoreAnd they over lubricate them that's a big reason why Glock pistols are sent back to the factory note work is over lubrication. They do require a lubricant but they do not require nearly.
What is nDLC coating?
GLOCK's nDLC provides tougher, more durable protection than previously used finish. The nDLC finish increases protection against corrosion and scratching and improves the ability of the pistol to function in adverse conditions. Ambidextrous slide stop lever.
What is Tenifer coating?
Ferritic nitrocarburizing or FNC, also known by the proprietary names Tenifer, Tufftride and Melonite as well as ARCOR, is a range of proprietary case hardening processes that diffuse nitrogen and carbon into ferrous metals at sub-critical temperatures during a salt bath.
Are Glock slides stainless steel?
Are Glock slides stainless steel? Unlike a number of other brands. Glock uses (at least AFAIK) carbon steel for their slides and barrels. A number of other brands uses stainless for these parts.Mar 22, 2020
Are Glock barrels heat treated?
SKU: Material used is 416R Stainless Steel heat treated to 40 Rockwell C. All barrels are broached and manufactured from bar stock material or forgings, depending on availability.
Are Glock barrels hardened?
They're a drop-in style barrel with extremely tight tolerances and milled from pre-hardened chromium 416R stainless steel originally designed for match grade rifle barrels.
Can you over lube your Glock?
It is important to remember that you do not want to over-lubricate a Glock. Glock pistols are in fact designed to function with only small amounts of lubrication. Over-lubricating results in large amounts of burnt and unburnt powder, brass shavings, dirt, lint and other foreign matter gathering to form sludge.May 4, 2015
Where do I lubricate my Glock?
2:024:17Oiling a Glock - YouTubeYouTubeStart of suggested clipEnd of suggested clipTwo three four then where the trigger bar meets the connector. One drop right there.MoreTwo three four then where the trigger bar meets the connector. One drop right there.
What is white lithium grease spray used for?
White lithium grease is used to keep components moving smoothly, free of friction and seizing. You can also apply it preventatively to protect against rust and corrosion. White lithium grease can be used to: Lubricate car door hinges.Aug 18, 2018
What is gun pannelizing?
Gun Parkerizing helps protect a steel surface from corrosion and increases its resistance to nicks and scratches by the submersion of the steel into a phosphoric acid solution. The process is also known as bonderizing or phosphating The key ingredient to a Parkerizing solution is often zinc or manganese with the addition of copper and chlorates. The solution is then heated to 190 to 210 degrees Fahrenheit.
What is bluing a gun?
Steel bluing, also known as gun bluing, oxidizing and black passivating, is a process by which the metal is given a rust-resistant finish. Bluing guns are achieved by an electrochemical process in which the iron in steel is converted to magnetite, or black oxide. Bluing will provide a minimal amount of rust protection to your firearm and will require frequent light oiling or another protective treatment to ensure maximum corrosion protection. A black oxide coating will not cause a dimensional change of the treated object and is one of the cheapest coating options available. The bluing process for guns will also allow a decrease in the glare effect of a treated piece.
How long does cerakote last?
Cerakote requires little maintenance and will last you for years before needing a touch-up. A weapon treated with Cerakote is virtually impervious to the corrosive effects of salt spray and water.
When was anodizing first used?
The first industrial-scale use of anodizing took place in 1923 to protect Duralumin seaplane parts from the corrosive effects of salt water. These early chromic-acid based applications were known as the Bengough-Stuart process. The first sulfuric acid anodizing processes were patented in 1927.
What is cold bluing?
Each of these processes are slightly different. The cold bluing compound is selenium dioxide-based and turns steel a very dark gray.
What is anodizing metal?
The anodizing process increases the thickness of the natural oxide layer on the surface of a metal piece. The name comes from the process itself. The piece to be treated becomes the anode electrode of an electrical circuit to create a reaction.
What is a cerakote coating?
Cerakote is a ceramic-based coating which is available in various colors. It is one of the simplest finishing options available if you're looking to custom-color your firearm. Unlike certain other finish types, a Cerakote coating will not attract abrasion-causing dust particles and offers superior lubricity to treated parts.
What was the original finish on the Glock 19?
The original finish on the first generation of Glock 19s, which were introduced in 1988, was a rough, non-glare, gray finish . The second generation, which was also introduced in 1988, had the same kind of finish. The Glock 19 Gen 1 was a transitional handgun, and not too many of them exist.
What is the Glock 19 made of?
It is still made of nylon-based polymer-2 and steel, still retains the same basic shape, and still holds the title of one of the most popular firearms in the world. There were, however, some differences between the releases, and one way of telling them apart is by inspecting the Glock 19 finishes.
How many generations of Glock 19 are there?
Over the years, the Glock 19 firearm has undergone several changes. There have been four separate releases of the Glock 19, such as the Glock 19 Gen 4, with the most recent one being introduced in the middle of 2010. Glock fans have long since applied the term “generations” to the releases, in order to describe these various incarnations of the Glock firearms. With the release of the fourth generation of Glock 19s, the company accepted the term as an inseparable part of the Glock’s heritage, and chose to emblazon the words ‘Gen 4’ on their newest batch of handguns.
When did the Glock 19 come out?
Well, Actually, it Isn’t. The latest version of the Glock 19. The Glock 19 has not radically changed since its introduction in 1988 – although a lot of people do change their Glock’s up with accessories or modifications.
Is Tenifer a finish?
Contrary to what many believe, Tenifer is not a finish. It is, in fact, a heat treatment which the gun’s steel undergoes, and which hardens the steel and protects it from corrosion, heat, and wear. Tenifer is even effective to a certain water depth. A treatment is applied before the finish.
Is Tenifer the same as Melonite?
Essentially, Tenifer and Melonite are the same thing, yet there are some users which state that there is a noticeable difference. Once an appropriate treatment has been applied, a finish (or coat) can be added. In the case of the Glock 19, the original Gen 1 and Gen 2 were finished with a Parkerizing process.
