- Clean your pool thoroughly BEFORE applying the shock treatment.
- Wait until the sun goes down to start the shock. The sun lowers the effectiveness of the shock chlorine.
- In a bucket, mix your pool shock chemicals into water from the pool until they dissolve.
- Run your pump and filter constantly while you’re shocking your pool.
- Pour the mixed and dissolved pool shock evenly around your pool or slowly in front of one of the inlet jets from your pool’s pump.
- Wait at least an hour after the shock and test the chlorine levels.
- The pool will be safe to swim in again after chlorine levels return to normal. ...
How often should you Shock Your pool?
There’s no hard and fast rule regarding how often to shock a pool. But there is a generally accepted guideline of once every 1 to 2 weeks to keep your pool water performing at its highest level. As long as you stay on top of things, you shouldn’t have any problems with unpleasantness when it comes to the state of your pool’s water.
How often should you shock a swimming pool?
- After a high bather load (e.g. A party)
- After a heavy rainfall or thunder storm
- After a water change
- At the start and end of the season.
How to shock a pool the right way?
What Types Are There?
- Calcium Hypochlorite. This chemical, also known as cal hypo, is one of the more affordable and practical strategies to shock your pool.
- Lithium Hypochlorite. Lithium Hypochlorite does not add additional calcium to your pool like cal hypo, but it is much more expensive for various reasons.
- Dichlor. ...
What is the best shock for a pool?
- Clears Cloudy Water
- Fast-Dissolving Pool Shock
- Six 13.4 oz Bags Of Pool Shock
Can you make homemade shock for pool?
Shock. Common unscented household bleach (sodium hypochlorite) works well to shock a pool. To increase the chlorine level by 5ppm in a 10,000 gallon pool, you would need 1/2 Gallon of basic household bleach.
How do I shock my above ground pool naturally?
Fill your pool with water. You can use water from the hose that is chlorinated. Chlorine & hydrogen peroxide can mix together just fine. To start treatment, shock your pool with hydrogen peroxide by adding 250 ml (1 cup) of hydrogen peroxide for every 1000 liters (250 gallons) of water.
What can you use in place of pool shock?
Bleach2. Bleach. Also known as sodium hypochlorite, simple household bleach (which contains 5.25 percent of sodium hypochlorite, the active ingredient in bleach) can get stains out of grout that the baking soda couldn't. Bonus Tip: Bleach can also be used to shock a pool.
How do you make shock for pools?
How do I shock my pool?Check that the pH levels in your pool are balanced.Prepare shock ahead of time in a 5-gallon bucket of pool water and stir.Ensure the pool pump is running. Pour the mixture from the bucket into the water around the edges of the pool.Let the pump run for about 6 hours or more and test the water.
Can I use baking soda to shock my pool?
A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool's pH tested below 7.2, add 3-4 pounds of baking soda. If you're new to adding pool chemicals, start by adding only one-half or three-fourths of the recommended amount.
Can I use hydrogen peroxide instead of chlorine in my pool?
What you may not know is that hydrogen peroxide is a powerful oxidizer that can be combined with ultraviolet light to disinfect swimming pools. The combination of ultraviolet disinfection with hydrogen peroxide allows pool owners to safely eliminate all chlorine in their pool or spa.
Can I use bleach instead of pool shock?
Bleach is safe and the only chemical you should be using in your pool unless cleaning pool tile with baking soda. So yes, you can use bleach to keep your pool water chemistry balanced.
How do you make liquid shock?
How to Superchlorinate your Pool with Liquid and Granular Chlorine12.5% Liquid Chlorine Pool Shock – Normal Dosage: 1 gallon of shock per 10,000 gallons of water. ... 75-78% Calcium Hypochlorite Granular Pool Shock – Shock Dosage: 1 lb (bag) of shock per 10,000 gallons of water.
Can I use household bleach in my pool?
It is important to know what exactly bleach is before you put it in your pool. Household bleach, Clorox and liquid chlorine can all be used to sanitize a pool. They are all types of chlorine. Household bleaches such as Clorox usually contain about 5-6% available chlorine, about half that of pool liquid chlorine.
What is pool shock ingredients?
Here are four main types of pool shock:Calcium Hypochlorite. Calcium Hypochlorite, or cal-hypo, is the most powerful and fast-acting shock available. ... Sodium Dichlor. ... Potassium Monopersulfate (Non-Chlorine Shock) ... Sodium Hypochlorite (Bleach or Liquid Shock)
How much bleach do I use to shock my pool?
If you need to calculate how much bleach or Clorox you need to shock your pool, you will have to use 1/2 gallon of bleach per 10,000 gallons of water to raise the chlorine levels by 5 ppm.
How do you shock a pool without chlorine?
Potassium peroxymonosulfate: A less costly, non-chlorine shock. Add it directly to your pool water at any time. Takes roughly 15 minutes to work before you can safely swim.
What is the best shock for a pool?
If bromine is used as your primary sanitizer/conditioner, this is the best type of pool shock for your pool. You can use any one of the 3 main types of pool shock for regular shock maintenance.
How to dissolve pool shock?
In a bucket, mix your pool shock chemicals into water from the pool until they dissolve.
What is a Pool Shock?
A “shock” simply refers to adding above normal levels of chlorine or sanitizer to your pool to quickly raise the levels of chemicals in a very short amount of time.
What to do if your above ground pool turns green?
You’ll definitely need to shock your pool and use some algaecide if your above ground pool’s water starts to turn green or give off a foul oder.
What is the strongest pool shock?
Cal-hypo is the strongest pool shock available. It’s quick dissolving, but should be pre-dissolved in a bucket before being added to the pool. Failing to pre-dissolve the pool shock can lead to liner bleaching or pin holes in the worst case scenario. The sun will eat it up pretty quickly, so it’s best to use cal-hypo pool shock at night. This type of pool shock is best if the water has already turned green. After shocking a pool with cal-hypo, you can swim again once the chlorine levels have returned to normal.
How long does it take to swim with potassium monopersulfate?
You’ll be able to swim after about 15 minutes of using this type of pool shock.
How to get rid of bacteria in vacuum?
Run your vacuum as you brush the sides and skim the top of the water. Chlorine works to neutralize organic matter and bacteria – the more you can remove before hand, the more effective the shock will be on the stuff you can’t see – like algae, skin cells, oils, etc. Nasty, I know!
What is Pool Shock?
Shocking refers to the process of putting non-chlorine and chlorine chemicals into your swimming water to eradicate algae and get rid of bacteria. Shocking your pool may end up being costly and time-consuming if you do not partake the whole procedure correctly. Therefore, you are advised to research on the process before putting it into practice.
How Often You Should Shock pool?
Shocking the pool is determined by the frequency with which the pool is used. In cases where the pool is used daily, do it at least twice a week. If the pool traffic is not high, you can do it once a week. Ensure you cover the pool after chlorination as this will protect the chlorine from UV rays from the sun that break and weaken the chlorine.
How to treat algae in pool?
Treating your ground pool water helps you to get rid of bacteria and green algae that may lead to sicknesses. With that in mind, diligence is required when engaging yourself in this process. Always wear protective gear to protect your eyes, since most swimming pool shocking chemicals are like bleaching agents. Be careful to protect your clothes and shoes to prevent them from staining. And as a rule of thumb, always add chemicals to water, not water to chemicals.
Can you shock an above ground pool?
It is essential to know the right pool shocking option for your above ground pool. For instance, if you use powder shock you cannot allow undissolved powder to settle at the bottom of the pool. If the powder does not fully dissolve, the shock hits the vinyl liner which ends up breaking or staining it.
When to use shock treatment in pool?
You’ll also want to apply shock treatment when opening the pool, and closing it down for the season. On opening, after you’ve balanced it’s pH level, shocking will sanitize and oxidize the pool, restoring its clear water. On closing, pool shock is used as a disinfectant to prepare the pool for the winter months.
What is pool shock?
Pool shock is a “super dose” of granular pool chlorine that oxidizes chloramines (combined chlorine) and kills bacteria in the water. Shocking depletes combined chlorine and increases free chlorine . If your chlorine levels are low, a chlorinated shock is required.
What is non chlorine shock?
Non-Chlorine Shock: Also known as Potassium Monopersulfate (MPS), this is a chlorine-free shock that oxidizes contaminants, but won’t rid the pool of bacteria. Compared to chlorinated shock, you can use MPS shock at any time of day and be swimming in the pool 15 minutes later.
What happens when you shock a pool?
By shocking your pool, you replenish your chlorine level and oxidize chloramines (combined chlorine), which are a gaseous irritant that are hazardous for human consumption.
Why do you shock a pool at night?
Pool shocking is usually done at night, when the sun no longer shines on the water. This is because UV rays destroy chlorine at near warp speed. Twilight hours give the shock an extended amount of time to effectively kill everything in its path.
Why does my pool smell like chlorine?
Chloramines irritate your eyes, nasal passage, lungs, and skin. If the pool has a very strong chlorine smell to it, you know it’s time to shock.
How many volts does a pool shock?
As a pool owner, you’re gonna need to learn how to shock a pool. Pool shocking doesn’t mean sending 5000 volts of electricity through the water (although that would be pretty cool to see). However, what it does refer to is the rebalancing of pool chlorine levels, keeping the pool water safe to swim in.
What causes scale in pool?
Scale is caused by calcium carbonate deposits.
Why do you add chlorine in the evening?
This is because chlorine breaks down by sunlight, which in turn, causes you to add more to obtain the desired results.
Can you add chemicals to a pool?
Adding chemicals to your pool and spa can get expensive rather quickly! Here are some common household items you can use to maintain a sparkling clean pool.
Can you use baking soda in a pool?
While it’s fine to substitute baking soda in the pool, it’s NOT okay to substitute pool/spa alkalinity products in your baking. Yes- people ask this. As a rule of thumb, 1.5 lbs per 10,000 gallons of pool water will increase total alkalinity by 10 ppm. The recommended alkalinity level for a swimming pool is 80-120 ppm.