/Salting-Water-58ebd6245f9b58ef7e798efb.jpg)
Turn on your filter system and add the correct amount of salt to the water for your pool size. Continue to run the filter for 24-48 hours or until all of the added salt is dissolved. Please refer to your filter’s instructions manual for proper installation instructions.
Full Answer
How do I add salt to my pool filter?
Turn on your filter system and add the correct amount of salt to the water for your pool size. Continue to run the filter for 24-48 hours or until all of the added salt is dissolved.
How hard is it to install a pool salt system?
Your salt system installation may be easier or harder depending on how tight your pool equipment pad is installed. Most people should aim to install the check valve near to the heater outlet, and the salt cell shortly after this.
How do I install a saltwater flow switch?
Flow switch location- If your salt system requires the installation of flow switch (such as the Hayward Aqua Rite) then you should install the flow switch with 10x the pipe diameter in a straight, unobstructed run, in front of the switch.
Can a salt chlorine generator provide 100% of my pool sanitation?
However, a salt chlorine generator can provide 100% of the sanitation your pool needs ONLY IF the other pillars of pool maintenance provide the needed support. Pillar #2 - Pool Circulation & Filtration
How do you hook up a saltwater pool pump?
6:0510:46How To Setup An Intex Saltwater Pool Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just screw that on it's pretty simple and then the nozzle inlet hose that comes with the saltMoreYou just screw that on it's pretty simple and then the nozzle inlet hose that comes with the salt water pump. Goes from the water outlet near the Electra load cell.
How do I hook up my Intex saltwater system?
1:5611:07KRYSTAL CLEAR SALTWATER SYSTEMS - Set Up InstructionsYouTubeStart of suggested clipEnd of suggested clipConnect the one and a half inch diameter short hose that came with a saltwater system to the inletMoreConnect the one and a half inch diameter short hose that came with a saltwater system to the inlet side of the saltwater system marked with a water flow arrow.
How do I add salt to my Intex above ground pool?
Add one 25-pound bag of salt for every 1,000 gallons of water. Do not use yellow or iodine salt. Go to a pool supply company, and get salt for the pool. If you're converting your pool from a chlorine-treated pool to a salt water pool, wait two days, so the chlorine dissipates.
How do I start my Intex saltwater pool?
2:5520:39INTEX SALTWATER SYSTEM with E.C.O. - YouTube - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then what I would do is get one bag at a ton of all the way around very slowly and then once IMoreAnd then what I would do is get one bag at a ton of all the way around very slowly and then once I got the one bag in I would use the brush. And I will just put on the pole. And dissolve all of the
What do you need to setup a saltwater pool?
Besides normal and good water balance, all you need for a salt water pool is a chlorine generator and enough pool salt to raise the level to the salt system manufacturer's recommendation. You will still need to maintain good water balance on a salt water pool.
How do you start a saltwater pool for the first time?
Spring into action: Tips for opening salt water poolsClear the cover. Debris should be removed with a leaf net and water should be pumped away before removing the pool cover. ... Clean and setup. ... Shock with chlorine. ... Use treatment products. ... Test and balance. ... Use pure salt. ... Ongoing maintenance.
How do you install a saltwater above ground pool?
Process To Install Salt System for Above Ground PoolStep 1: Choosing The Right Salt Chlorinator. It is recommended to use at least a salt system that is at least 1/3 larger than your pool size. ... Step 2: Install The Salt System. Unplug all the pool components and locate the filter pump. ... Step 3: Know Salt Level and Add Salt.
Can you use a regular pool pump for salt water?
They also need to have some chlorine added at the beginning of the season and after heavy uses to maintain a safe level of chlorine in the pool. You need a special pump and filter to run a salt water pool. There is no such thing as a “salt water pump” or “salt water filter”; any pool pump or filter will do just fine.
How many bags of pool salt do I need?
Most saltwater pools need a salt level of between 2,500 and 3,500 ppm of salt. A regular 40 lb (20 kg) bag of pool salt will raise the pool salt level by 450 ppm for every 10,000 gallons of pool water. For a 10,000-gallon pool with no salt in it, you will need about 7 bags of salt to get 3,000 ppm of salt.
Steps to Open your Swimming Pool
Turn on your filter system and add the correct amount of salt to the water for your pool size. Continue to run the filter for 24-48 hours or until all of the added salt is dissolved.
Pool Capacity Cheatsheet
Add a chlorine stabilizer at a rate of 1 LB per 5,000 gallons of pool water.
About The Pool Factory
America’s Above Ground Pool Experts – is the best place to find everything you need to make owning a swimming pool or spa fun and easy, at the best prices today. With a combined 50+ years of experience The Pool Factory employs a highly trained staff of above ground and semi inground pool specialists.
How much pressure should a pool filter be?
As a good rule of thumb, your pool filter typically only needs to be cleaned out when its pressure gauge rises 8-10 PSI over its normal baseline.
What is the oxidizer in a pool?
For any pool, sanitation requires an "oxidizer" - traditionally liquid, granular, or tablet chlorine (or a combination of any). Instead of buying and lugging large quantities of buckets or jugs of conventional chlorine, salt pools naturally generate free chlorine at a constant rate. Your role is to ensure sufficient sanitation.
What happens if you don't have sanitation in your pool?
A swimming pool without sanitation will have water that is green, opaque, and smelly. It's also potentially dangerous: micro-organisms can thrive and multiply uninhibited, and it can harbor disease-spreading pests. For any pool, sanitation requires an "oxidizer" - traditionally liquid, granular, or tablet chlorine (or a combination of any).
What is balance in pool water?
Balanced water chemistry means it's easy to have clean & clear pool water with minimal intervention. In contrast, imbalanced water chemistry makes everything harder: it can take dramatically higher amounts of sanitation to maintain proper chlorine levels and keep algae at bay (if you even can!); it can require longer pump run times and more filtration; it can cause hard-to-clean mineral scaling; it can cause dangerous water conditions for your swimmers, pool equipment, and/or pool surfaces!
How often should a pool pump run?
Ideally, your pool pump should be set to run long enough to circulate 1-2 times the amount of water in your pool through the pool filter each day. (If you don't have an estimate of your water's flow rate, you can consider the relatively easy addition of a flow meter .)
What is the range of salt chlorine?
It simply needs to be in range so that your salt system can perform its sanitation work. The range for most systems should be between 3000ppm and 4500ppm, though different systems may have different ranges.
What is the 4th pillar of a pool?
Pillar #4 - Practical Maintenance. Any swimming pool needs a little regular attendance, especially if it is outdoors. Check your pump and skimmer strainer baskets regularly. Leaves, bugs, and other debris will collect there and may plug up your system.
Why do pool owners pay for salt?
All too often pool owners pay for the installation of a salt system only to encounter serious problems months or years down the road - problems directly as a result of an inadequate installation of the salt system.
How many volts does a salt water system need?
It will also require either 110 volt or 220 volt power depending on which brand and model you are installing. While most salt systems will have an external control box there are some models, such as Pentair IntelliChlor system, which have the control panel integrated into the generation cell itself.
What is bonded pool equipment?
Bonded pool equipment - If you are going to increase the salt content in your pool then you need to be sure that your pool, and pool equipment such as pump and heater, are bonded. You should be able to locate a bonding wire that attaches to a bonding lug on your pump and heater.
How long does it take for salt to dissolve in a pool?
First, you should always have your salt system powered completely off when you add salt to the pool. Salt will take around 24 hours and a few brushings of the pool floor in order to dissolve. During this time if your system is attempting to run there can be a spike in the salt content that passes through the cell which can cause a system failure. This is also the same reason that you should never pour salt into the skimmer of your pool. The salt should be dumped directly into the pool body and brushed with your maintenance pole and brush.
Is salt chlorinator a DIY project?
Salt chlorinator installation is a "DIY" level project if you are a handy person however there are a number of technical concerns that must be addressed before you start dumping salt into your pool. If you are not familiar with me, you should be aware that I have a lot of strong words for salt water in swimming pools.
Is it hard to install a salt water generator?
Installing a salt chlorine generator is not very difficult - Cutting and gluing PVC pipes + balancing your water.
Is it hard to install a salt cell?
Installing the cell is not hard - knowing where to install it is the important part. Your salt system installation may be easier or harder depending on how tight your pool equipment pad is installed. Most people should aim to install the check valve near to the heater outlet, and the salt cell shortly after this.
