At any time you can also apply xylene to the roller to thin out and remove excess Durabak. As soon as the first coat is touch dry, the second coat can be applied (usually one to two hours). Each coat should be applied in thin layers.
Full Answer
Can you thin Rust-Oleum bed liner?
Rust-Oleum Truck Bed Coating is ready to use. Do not thin or tint. For best results, apply Truck Bed Coating with Rust-Oleum Truck Bed Applicator Kit (sold separately) and follow all directions accordingly or apply using a high quality solvent resistant foam roller.
How do you spray a rustoleum truck bed liner?
Hold can upright 10-12" from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can in motion while spraying. Remove any overspray from the auto finish immediately. For best results, apply 2 coats, allowing 1-2 minutes between coats.
How do you prepare a Rust-Oleum bedliner?
1:154:20How To Apply Rust-Oleum Truck Bed Professional Grade Kit - YouTubeYouTubeStart of suggested clipEnd of suggested clipPower wash or scrub your entire truck bed with soap. And water make sure to rinse well and towel dryMorePower wash or scrub your entire truck bed with soap. And water make sure to rinse well and towel dry all surfaces rough up the truck bed surface. And D gloss it with a sanding sponge.
Is Rust-Oleum bed liner oil based?
Rust-Oleum Truck Bed Coating Flat Black Enamel Oil-based Interior/Exterior Paint (1-quart)
How many coats of Rustoleum are needed?
Only one coat is required (except for the color White, it needs 2 coats). If a second coat is desired for your project, after applying the entire floor with the first coat, wait 6 hours before applying the second coat.
How long does Rust-Oleum Truck Bed Coating take to dry?
Allow 48 hours for full cure before placing objects in the truck bed. Minimum dry time of 24 hours should be allowed before placing objects in the truck bed. Allow the coating to dry for 24-48 hours before subjecting to light duty.
How do I prepare for bed liner?
0:002:07How To Prep And Apply Truck Bed Liner - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd other parts of the truck that you don't want dura back to cover rough up the truck bed with 80MoreAnd other parts of the truck that you don't want dura back to cover rough up the truck bed with 80 grit sandpaper. And once it's clean wipe it down with xylene. And let it dry mix.
How do you prepare aluminum for bed liner?
You need to use a zinc self etching primer on the aluminum panels before you paint or use bedliner on them. I use the Rust-Oleum self etching primer in a spray can and it makes all the difference. I scuff the panels with a course scot-brite pad, with them down with acetone and then I use the self etching primer.
Can you spray bed liner over rust?
Yes, you can apply/spray raptor liner on rust. Before going about that, make sure you reduce down the rusts to bare metal. After applying the spray on the bare metal, which was a rusted surface, you can either paint it or use a Bedliner material directly over it.
What is the best coating for a truck bed?
About Truck Bed Coating 1 Durable abrasion resistant 2 Textured finish that forms to the contours of a truck bed 3 Rust protection from Stops Rust formula 4 Pick your preferred DIY application from spraying and rolling to brushing 5 Multi-purpose coating for truck beds, fenders, step areas, trailer floors and more
What is rust oleum coating?
Rust-Oleum® Truck Bed Coating is the choice for recoating and restoring worn, unfinished or previously finished metal truck beds. When used with Rust-Oleum Truck Bed Applicator Kit (sold separately), this easy to apply polymer coating not only helps prevent truck bed damage caused by scratches, rust and weather, but it also enhances your vehicle's appearance.
What happens if a truck bed rusts?
All of the metal pieces of your truck are interconnected, so if rust begins in your truck bed, it can quickly spread deep into the structure of your truck, the chassis and then weaken your entire vehicle. Engine rust can do the same and lead to mass corrosion.
What to use after roughing up a car?
After roughing up the surface, clean off all dust and debris, and wipe down with xylene after cleaning (assuming no primer has been used).
Where to start on a truck bed?
Most of the time, it’s best to start with the front and side panels ; since there’s a good chance you’re going to be in the truck bed yourself! Then, move to the floor of the truck and apply there as well.
How to mix Durabak bed liner?
First, thoroughly mix Durabak™ Truck Bed Liner using a drill or stir stick only (the preferred temperature should be above 60 degrees F, and humidity above 40%). If you find that your Durabak™ Truck Liner is too think to accurately brush or roll, feel free to thin it up to 10% with xylene. Take care to stir the mixture throughout the application process.
Can a truck bed be wet?
A wet truck bed will also make the install that much more difficult so make sure it’s dry before moving forward.
Can Durabak truck liners be installed?
Believe it or not, when folks ask us, we tell them that the install for our Durabak™ truck liners is pretty simple. The hardest part is getting the truck prepared!
Can you use a spray gun to apply Durabak?
If you prefer to use a spray gun, after you read the preparation guide, scroll on down to the spray application section, where we’ll break down what you’ll need to apply Durabak™ with your spray gun!