Dial Liquid Evaporative Cooler Cleaner
- Add to the evaporative cooler's fresh water supply, and circulate through the cooler pads for 20-30 minutes
- Drain cooler and re-fill with fresh water
- Helps dissolve scale and mineral buildup
How do I clean the dura-cool™ pad?
Clean the Dura-Cool™ pad and add a small amount of washing machine fabric softener or use Dial's Fresh-Air™ to eliminate or reduce channeling. Replace pads if necessary. I use Dura-Cool™ pads. When operating the cooler during a strong wind, water was drawn into the air duct. How can this be prevented? Use 2 Dura-Cool™ pads in each pad frame.
What is cooler coating and how do I use it?
Our high-grade Cooler Coating can prolong the life of your evaporative cooler. It protects against rust and corrosion in metal coolers. Apply to the interior pan of the cooler at the first sign of rust.
Can my cooler controller™ be repaired?
Cooler Controllers™ cannot be repaired. Can the default temperature be changed? No. The default temperature is factory pre-set to be 77° F. My Cooler Controller™ now shows temperature in deg C?
What should I look for when replacing a cooler motor?
When replacing a cooler motor, always choose the same horse power, speed and volt rating. Apart from the obvious difference in price, are there any other differences (performance/lifespan) between the standard, the brass, and the heavy-duty bronze float valves?
How do you remove calcium from evaporative cooler?
#3 How to Remove Calcium Deposits from Swamp Cooler Pads The best cleaner is a simple mix of white vinegar and water. You should clean the water pan reservoir at the bottom of the cooling unit at least once a month throughout the season to prevent minerals from building up inside.
How long does cooler coating need to dry?
24 to 48 hoursCure Time Guideline: Coating cure time is dependent upon a number of conditions (temperature, humidity level, etc.), but mainly the coating thickness. The thicker the coating the longer the cure time. Typically, properly applied coating should cure within 24 to 48 hours.
Can I put CLR in my swamp cooler?
Clean clogged shower heads (they work like knew) just take the shower head off set it in a bowl of water CLR mixed about 50/50 for about an hour.. Then rinse. Swamp Coolers I unplugged the motor to the fan and just put the CLR in the water tub.
How do I stop my evaporative cooler from smelling?
Ways to Help Deodorize Your Swamp CoolerPurchase a swamp cooler deodorizer – You can purchase a swamp cooler deodorizer to place in your swamp cooler from most home improvement stores. ... Let your pads dry – If the temperatures are easing a bit you may want to run your cooler with the fan only to allow the pads to dry.
How do you paint a cooler without sanding?
Apply a spray-on plastic primer to the surface of the cooler. A plastic primer will help the paint adhere to the surface of the cooler better. Spray the primer on the cooler so there's an even coat over the entire surface. You can find a spray-on plastic primer at your local home improvement center or paint store.
How do you prepare a cooler for painting?
How to Paint a Cooler – 8 Steps ProcessStart with some Spackle and Sand Paper. ... Apply the Primer. ... Get some cool Designs for your Cooler. ... Transfer your Designs onto your Cooler. ... Paint over your Design. ... Let your Paint Dry. ... Apply Sealer. ... Waterproof your Cooler.
Can I run vinegar through my swamp cooler?
Clean. Add a cup of vinegar to the cooler pan and let the vinegar cycle through the system for up to an hour. This will eliminate odors, mold, mildew and some corrosion, calcium deposits and other types of build-up.
Can I put bleach in my swamp cooler?
Bleach is one of the most common household cleaning chemicals, but it is not a good choice for your swamp cooler. Bleach should never be used in an evaporative cooler as it can damage the pans and possibly void your warranty. We recommend a cleaning solution made from a mix of vinegar and water.
How do I descale my air cooler?
How To Clean Air Cooler At HomeStep 1: Remove The Panel/Cooling Pads. Firstly, remove the panel or cooling pads of your air cooler. ... Step 2: Clean Cooling Pads. ... Step 3: Drain The Water And Clean. ... Step 4: Wipe The Interiors With A Wet Cloth. ... Step 5: Reassemble All The Parts.
How often should you clean evaporative cooler?
STEP #3: Check And Clean The Cooling Pads No matter what type of evap cooling pads your system has, it is important to clean them at least once a month. Clean the evap cooler pads at least once a month. If you don't clean them more often, they can cause bad smells.
Why does my evaporative cooler smell like fish?
The cooling pads, which are typically saturated with water to produce cooling, may have developed mold and / or mildew. When the system runs, it may be emitting this fishy or moldy smell, as a result. This is especially common if you have been running the swamp cooler constantly, and water has been continuously used.
Why do air coolers stink?
When water is first introduced to the cooler the glue that holds the media together may emit an odor that smells offensive. This smell will go away after the media has been soaked well and rinsed.
Special offers and product promotions
Amazon Business: Make the most of your Amazon Business account with exclusive tools and savings. Login now
Have a question?
There was a problem completing your request. Please try your search again later.
Product description
A mild acid cooler cleaner with wetting agents for pads. Quart. Material: Size: 1 Qt. Size of Straps: Color:
Featured items you may like
Pages with related products. See and discover other items: humidifier mold prevention
