Why choose ATS for water treatment?
Once water has served its many residential and commercial uses, it must be treated to be reused, treated to enter the public utility wastewater treatment process or treated to return to the environment in a manner consistent with water quality regulations. ATS can handle your dewatering and sludge management needs.
How can ATS help with sludge management?
ATS can handle your dewatering and sludge management needs. ATS can discharge water from your project within the prescribed requirements and still save money on the disposal of your waste material.
How do I return a part to Aqua treatment service?
Upon approval by Aqua Treatment Service, Inc., the Dealer/Distributor should return the item to Aqua Treatment Service, Inc. 194 Hempt Road, Mechanicsburg, PA 17050 (prepaid). If a part proves to be defective, it will be repaired or replaced and returned to the Dealer/Distributor freight paid.
How many parts are in a kit ats-4025?
KITS ATS-4025 Kit: 5 thru 10 ATS-5177 Lens Kit: 2 thru 4 36 DWSW-8 Explosion 37 DWSW-8 Parts List CODE PART# DESCRIPTION QTY.
How do you replace quartz sleeves?
1:283:05LUMINOR BLACKCOMB How to replace the quartz sleeve on your ...YouTubeStart of suggested clipEnd of suggested clipUnscrew the gland nut from the reactor exposing the end of the quartz sleeve. Remove the quartzMoreUnscrew the gland nut from the reactor exposing the end of the quartz sleeve. Remove the quartz leave and oring by gently twisting and pulling the sleeve.
How do I change my UV light water filter?
3:187:16Ultraviolet Water Filter - UV Bulb Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can discard the old bulb in your general trash. And then remove your new bulb. From the packing.MoreYou can discard the old bulb in your general trash. And then remove your new bulb. From the packing. And install it in the chamber.
When should I change my UV light?
UV lamps should be replaced once every 12 months. UV lamps have a lifespan of approximately 9,000 hours. Calculated out, this means the lamp can operate for about 375 days before requiring a replacement.
How do I reset my ATS UV light?
Unplug the UV lamp from the Lamp connector. Replace with a new UV Lamp. Make sure the control box is plugged into the wall outlet and the UV lamp is on. Press and hold the reset push button.
How often should you change your UV light in a water system?
every 9,000 hoursYou should remember to replace your UV bulb every year or every 9,000 hours of use (whichever is sooner) as this not only helps maintain the level of protection but can help prevent anything going wrong with the system as a whole.
How do you clean a UV light?
You don't need to remove the lamp to clean it. Wipe the lamp with a damp sponge, using only water. If there is residue on the lamp, you can use Windex or other household glass cleaner by spraying on a sponge or cloth, then wiping the lamp. Follow with a damp sponge using only water.
How do I know if my UV light is still good?
A UV lamp should not be kept running after 3 years. The UV system should just be turned off until the lamp is replaced, because it effectiveness is spent and it will simply waste energy. The excessive energy consumed by an aging lamp can cause the power supply to overheat, potentially causing a complete system failure.
How do you change a UV light?
Remove the lamp/sleeve assembly along with the sleeve bolt from the chamber. Unscrew the UV lamp by holding the sleeve bolt. Unscrew the sleeve bolt and remove o-rings from the quartz sleeve. Clean or replace the quartz sleeve.
How long does a water UV light last?
9000 hoursHow Often should a UV Water Filter Lamp be Replaced? Unlike regular light bulbs, UV Lamps do not burn out – they solarize. This means that over time they reduce in their light wave intensity to about 60% of what a new UV lamp provides. This point is reached usually after one year, or 9000 hours, of continuous use.
How do I change a UV sterilizer bulb?
How to change a uv light bulbTurn the power off, all of it. I would recommend just unplugging / powering down the unit from the wall.Take your old lamp out. ... Put your new lamp in. ... Turn the power back on.Have a cup of tea.
Why is my UV light beeping?
Your UV or Ultraviolet Disinfection System is beeping because there is something wrong, so one of these things has put it into alarm. Your sensor may be dirty, so check that first. The timer has triggered because it has been about a year since the UV lamp was changed and now it is time for a new one.
How do I reset my Rainfresh UV light?
The lamp-change timer is reset by depressing the timer button while reconnecting ballast to electrical outlet and keep the button depressed until the ballast emits a solid three-second beep. This will re-set the lamp-change-timer to zero and the 3-second beep will confirm that the re-set was successful.
Stormwater Treatment
Stormwater is a problem because it carries a lot of pollution along with it wherever it flows. In urban areas much of the land is covered by impervious surfaces such as streets, buildings, parking lots and driveways.
Groundwater Treatment
Due to its instant availability and quality, Groundwater has become the prime source of drinking water among common people. Almost fifty percent of the world population depends on groundwater for their daily drinking water supply.
Industrial Wastewater
Once water has served its many residential and commercial uses, it must be treated to be reused, treated to enter the public utility wastewater treatment process or treated to return to the environment in a manner consistent with water quality regulations.
Sludge Dewatering
ATS can handle your dewatering and sludge management needs. ATS can discharge water from your project within the prescribed requirements and still save money on the disposal of your waste material.
Engineering Services
Active Treatment Systems has a wealth of experience in consulting, engineering, lab testing, dewatering and treating stormwater, groundwater and industrial wastewater from large complex systems to small municipal systems.
Lab Services
Your analyses are performed by well-trained scientists in a state of the art laboratory that was designed specifically for your needs. Services include balances, standard volumetric labware and chemicals, polymer/coagulants testing.
How to clean a quartz sleeve?
To clean the quartz sleeve, turn off the water flow to the disinfection unit, turn power off, and disconnect the electrical service to the lamp pins. Carefully remove the U.V. lamp. Loosen the compression nuts with O-Rings and remove the quartz sleeve while draining the water from the chamber.
What cord should I use for a disinfection system?
If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less Amperes or Watts than the disinfection system rating may over heat. Care should be taken to arrange the cord so that it will not be tripped over or accidentally pulled from the outlet. 1.
