To bypass your whole house filtration system, simply locate the bypass valve and press or twist it to activate the bypass. Some water filters have a bypass valve that’s attached to the unit or mounting bracket, while others come with separate bypass valves that are installed next to the unit.
Full Answer
How do I use the bypass button on my hard water?
Once you are finished using your hard water, simply turn your knob or handle all the way back counter-clockwise. Locate the bypass button. Firmly push in on the button until it goes all the way in. You may need to exert a lot of pressure especially if you haven't used it before or if it has been a while since your last bypass.
How to bypass a water softener?
How to Bypass a Water Softener Method 1 of 3: Using a 3-Valve Bypass. Find the valves by following the 2 large hoses running out of the water softener. Method 2 of 3: Operating a Single-Valve Lever-Type Bypass. Locate the bypass valve near the tubes running off the water... Method 3 of 3: Bypassing ...
How do you turn on a 3 Valve Bypass?
The 3 valve bypass has 2 valves plumbed on either side of the system that are normally “open” and one valve in the middle that is normally closed. Turn both outer valves off by rotating “clockwise”. Then turn on the center valve by rotating “counter clockwise”.
How do I use the bypass button on my Device?
Locate the bypass button. Firmly push in on the button until it goes all the way in. You may need to exert a lot of pressure especially if you haven't used it before or if it has been a while since your last bypass. Tip: If you are having trouble pushing in the button, try turning it clockwise for one or two rotations to loosen it up.
How do you turn off a soft water system?
To turn off a softening system, you should either press or turn the bypass valve to the opposite side, and unplug the softener from the power outlet.
What position should my water softener bypass valve be in?
It depends on the design of the valve, but it will usually be pointed left. A valve that's in bypass will usually be turned clockwise.
Will water softener regenerate if bypass is on?
Yes. In fact, a water softener automatically goes into bypass mode during regeneration, sending unsoftened water through your water heater and arou...
How do you bypass a Kenmore water softener?
Kenmore softeners use a bypass handle, so move the handle in the opposite direction to bypass the softener.
How do you bypass a Fleck water softener?
Most Fleck softeners use a lever valve, so turn the lever to bypass the softener.
How long is it safe to keep a water softener in bypass mode?
You could technically keep your softener in bypass indefinitely as long as the unit was drained, but your home would no longer be protected from li...
Can you bypass a whole home water filter?
Yes. Even if your filter doesn't come with an included bypass, you can still get a separate valve installed to send water around the filter when ne...
Do you need a bypass for a water filter?
No, bypass valves aren't absolutely essential. However, they're incredibly handy, ensuring that you always have a supply of drinking water - even w...
What does bypass mean in a filter?
Bypass means that water is flowing around a horseshoe bend inside the bypass, and flows straight into your home's pipes, skipping the filter.
How do you bypass a whole house filter?
A quality bypass lever valve is the easiest way to bypass a whole-home water filter. Follow our installation steps to learn how to install this val...
How do bypass valves work?
Bypass valves control the direction that water flows. Depending on which way the bypass is facing, water flows directly into the filter, or diverts...
Do water filters come with bypass valves?
Often, yes. Many filers have an installation kit (this could be included or an optional extra), including items such as a mounting bracket, bypass...
How long can you bypass a water filter?
There's no recommended minimum or maximum period to keep your filter in bypass mode. Just keep in mind, though, that the longer your filter isn't i...
How to bypass Peterson salt water treatment?
Move the lever sideways to activate the bypass - Image Source: Peterson Salt & Water Treatment Co. Step 1: Locate the level bypass valve. Step 2: Move the level to bypass mode. Most units will have this written on them. If not, you simply move the lever to the opposite side of where it currently is . Step 3:
When to put water softener in bypass?
Put your water softener in bypass when you are watering your lawn or garden. There are times when you may not require soft water or you may want to conserve water and salt. Maybe you are planning to use a large amount of water and it doesn't have to be softened. For example you could be: Watering your lawn or garden.
How many types of bypass valves are there for water softeners?
There are 3 main types of bypass valves for water softeners. Most residential units will have either a valve that you either push in or turn to put your water softener in bypass. Commercial softeners often have a three valve bypass operation. To find out what type of bypass valve your water softener has, take a look at the top or the back or top ...
What is a turn to bypass?
A turn "to bypass" unit will have a one or two handles or knobs that you can turn. A "push to" bypass unit will have a button that you can push in. A lever style bypass has a lever that you can move from side to side. If you have a commercial unit, you may see three separate valves connected to the pipes that are attached to your softener.
Can you trust WaterSmart for a water softener?
If you need your water softener repaired in the Kitchener-Waterloo region, you can trust WaterSmart. We'd be happy to help you with any repair or service on any type of water softener you have, at a reasonable rate.
Where is the bypass valve on a water softener?
The bypass valve is the third valve located between the inlet and outlet valves on the main pipe. Turn it 90 degrees so the wings run parallel to the main pipe to open it and start bypassing the water softener. The water system is now just running the normal water service without sending anything to the water softener.
Where is the water softener located?
If you aren’t sure where the water softener is located, check near the water heater. Water softeners are usually installed near the water supply inlet for the building, which is often in a basement or garage. Tip: Some push-push-type valves have colored knobs indicating which setting it is on.
How to bypass 3 valve water softener?
Turn both outer valves off by rotating “clockwise”. Then turn on the center valve by rotating “counter clockwise”. Now the water is flowing past the softener and not through it. To put your softener back in service, reverse the operation – close the middle valve (turn clockwise) and open both side valves (turn counter clockwise).
What is the phone number to bypass a leaking water line?
If you need to bypass your system because of a leak please call 402.826.3372 or 800.422.6885 right away.
How to put a softener back in service?
To put your softener back in service, simply turn the knob “counter clockwise” all the way until it stops. DO NOT over-loosen or over-tighten the valve to prevent damaging it. When it stops turning don’t try to force it further. The third type of bypass systems used on our equipment is the “3 valve” bypass.
How to get sediment off o-rings?
Turn it one or two full turns to loosen built up sediment on the o-rings inside – DO NOT TURN IT COUNTER CLOCKWISE. You can also try turning on a large faucet such as the bathtub. This will help relieve water pressure on the valve and may make it easier to push.
Does Culligan have a bypass valve?
It allows the water coming into your home to “bypass” the softener should you have a problem or want to use hard water to water your lawn or garden. Culligan uses 3 main types of Bypass valves. The one on your system will be easily identified by looking behind the control head of your system ...
Slider
For treated water, white side of slider should be pressed in and black side should be out. To bypass, push in the black side of slider. The white side will be out.
3 Ball Valve
For treated water, the center yellow valve must be closed and the in and out yellow valves should be open.
Stop Valves
For treated water, center valve must be closed and in and out valves must be open. To bypass, open center valve and close the in and out valves.
Discounts for Seniors!
If you are a new customer, and a Senior Citizen, you may be eligible for discounts on services and new installs. Call us today to find out more!
