how much lucas oil treatment on 04 ford f150

by Dr. Abagail Langworth Published 3 years ago Updated 2 years ago

Add 1.5 Ounces to each quart of oil. That would be 9 ounces on your Ford. Add it directly to the engine oil.

Full Answer

How much Lucas Oil should I add to my engine oil?

Apr 18, 2011 · Originally Posted by shortride. Lucas and other oil additives are designed for older engines. If you want to do anything with your oil switch to full synthetic after about 10,000 miles. Yea I'm going to start running the motorcraft semi synthetic it looks better than conventional oil.

Does Lucas Oil void warranty on new cars?

Dec 23, 2012 · If you are in a situation where you need thicker oil buy thicker oil, it will be cheaper and have the proper additives. It's more of a stabilizer. I ran 6l of mobile 1 5w20 and about …

Can you mix Lucas Oil and transmission fluid?

Apr 04, 2020 · The typical ratio is 20 percent Lucas Oil engine oil treatment to 80 percent of your vehicle’s specified oil with each oil change. For Ford Powerstroke engines, 1 quart of pure …

How much oil stabilizer do I put in a Ford PowerStroke?

Jan 19, 2011 · That would be 9 ounces on your Ford. Add it directly to the engine oil. Drive the vehicle for 200 miles and then change oil & filter. If the ticking is still there, add another 9 …

See more

Nov 02, 2008 · Ford F-150 / F-Series Generations. 2004 - 2008 Ford F-150. If you shop at Amazon.com (for anything), use this link to help support FordF150.net! ... I beg to differ Hound, …

How much Lucas Heavy Duty Oil Stabilizer should I use?

In engines: Use approximately 20% or one quart to each gallon of any plain motor oil. Petroleum, or synthetic. In badly worn engines: Use more — up to 60% or 80% if necessary.

How many ounces of Lucas Oil Stabilizer should I use?

In engines use approximately 20% or one quart to each gallon of any plain motor oil, petroleum or synthetic. In badly worn engines, use more • up to 60% or 80% if necessary. In manual transmissions and transfer cases use 25% to 50%. In differentials use 25% to 50%.

What is ratio for Lucas Oil?

Lucas High Mileage Oil Stabilizer is meant to be used as an additive to existing engine or transmission oils. Maximum lubricity is achieved with a mix ratio of 20% Lucas High Mileage Oil Stabilizer to 80% engine / transmission oil.

Does Ford recommend oil additives?

Ford, and I think all major manufacturers, DO NOT recommend any additives for their vehicle's oil.Oct 13, 2016

How much Lucas Fuel Treatment do I use?

Directions For Use

The recommended dosage is 2-3 ounces of Fuel Treatment for every 10 gallons of gasoline or diesel fuel. Pour Lucas Fuel Treatment directly into fuel tank. Exceeding the recommended dosage is not harmful to your vehicle. 5.25oz Bottle - One bottle treats up to 25 gallons of fuel.

Can Lucas Oil damage your engine?

You should avoid using petroleum distillates in your oil stop leaks and make sure that the products you purchase are certified by the EPA. These additives can cause long-term engine damage.Dec 3, 2021

Can you mix Lucas with synthetic oil?

A: Yes, In addition to being great for your engine, you can also mix it 25% / 75% a manual transmission and 50% / 50% in the differential. Lucas Oil Stabilizer blends with any petroleum-based or synthetic oil, and is formulated for gasoline or diesel engines.

How often should I use Lucas Upper Cylinder Lubricant?

How Often Can You Use Lucas? Lucas Fuel Treatment can be used as often as you like. Lucas Fuel Treatment does not contain any solvents, so every fill-up is perfectly safe. Fuel mileage is an improvment in fuel mileage, which is why many of our users run our fuel treatment with every tank.Dec 3, 2021

Does Lucas High Mileage work?

Lucas is a great choice for any high-mileage vehicle, it really works.Dec 3, 2021

What brand oil does Ford recommend?

Motorcraft^® motor oil

Ford recommends using Motorcraft^® motor oil for your Ford vehicle.

On 2007 5.4 triton three valve motor does timing changes need to be two links oner letter on the phaser cam gear and single colored on dot on cam gear

Ford 5 4L 3v Engine Timing Chain Kit Replacement Pt 4 of 4 Timing and...

I have a 2004 ford f150 making a tapping noies can it be the cam phasers going bad

check oil level ---yes it can but tapping noise can be a lot more reasons --worn oil -low oil pressure--low oil level--rocker loose-worn or damaged lifter-worn damaged valves --timing chain --water pump--pulley --really anything can cause a tapping noise --try to isolate the area or sound and diagnose problem

I have a 2004 F150 XLT 5.4L. Whilst driving the vehicle runs great but intermittently when coming to a stop the vehicle will shake like it is running out of fuel then just die. It will immediately start..

Do you know anything about VCT - Variable camshaft timing ? ETC - electronic throttle control ?

I just changed my oil in my 98 ford explorer and now i can hear a ticking sound coming for the passager side of the truck what could it be?

I asked because I had a suspension this was a 4.0 SOHC, have you had the recall done addresses the noise, it is caused inmost cases by leaking hydraulic cam chain automatic tensioners, they were recalled back in late 98, it is a free repair if it hasn't been done already. they are easy to change out.

I have a ford f150 with the 5.4 triton what is the cause of the engine tapping noise on the right side only. I was told this is normal for that engine type. but how can it be stopped if you dont like the..

it sounds like a broken exhaust manifold stud. But cam phasers can be noisy.

I have a ticking sound when my engine is running, should I use a thicker oil?

No, absolutely not. The ticking you are hearing are the lifers starving for oil or they are out of adjustment. Using a heavier weight oil will just make it worse. You need to make sure you are using the correct weight oil. Your 2005 Ford F150 requires 6 quarts of 5w20 weight oil with filter change.

Tapping or knocking noise in 2009 f150 4.6 3v engine

Tell them you heard about a recall for the CAM PHASERS. When the noise is present and you rev the engine to 2000RPM the noise will fade away. This verifys the CAM PHASERS are acting up.

Treatment FAQ