how much hydrogen peroxide does a well water treatment system use

by Miss Shania Trantow Published 3 years ago Updated 2 years ago

How much peroxide you will use depends a lot on how much iron and sulfur you are removing from the water as well as how much water your family uses. Typically we see 5 gallons (1 box) of peroxide last anywhere from 1-3 months.

See more

This hydrogen peroxide comes in many strengths. Store-bought is 3%. That’s generally safe. The type that we use is, and we can ship safely, and still considered relatively safe, is 7%. Mainly because it’s safe to handle, it’s not hazardous. You can often find 35% commercial peroxide locally, and it is usually cheaper. Much cheaper, by the way.

How much hydrogen peroxide do I put in my well?

You should generally inject 1.0 ppm of hydrogen peroxide for each part per million of iron or manganese, and 2 ppm of H2O2 for each 1.0 ppm of hydrogen sulfide gas (the cause of rotten egg smell in water).

How do you use hydrogen peroxide in well water?

Pour it into your well; the amount should be based on the problem's severity. The more widespread the bacterial infestation, the more hydrogen peroxide you should use. Once you're done, run the faucets in your house and check whether the hydrogen peroxide has gone deep into the water system.

Can you pour hydrogen peroxide in your well?

Batch treatment of the well with hydrogen peroxide not only rids the well of the odors from the sulfides and bacteria causing it (including slime mass), it also leaves behind a residue of excess oxygen than helps prevent future anaerobic conditions.Jan 23, 2004

What is the ratio of hydrogen peroxide to water for disinfecting?

The typical 3% hydrogen peroxide concentration found in stores can be used as a disinfectant, or you can dilute it to a 0.5% concentration, which still has some effectiveness, using a mixture of 2.5 parts water and 0.5 parts 3% hydrogen peroxide.Dec 18, 2020

How do you remove sulfur from well water?

Increase the water heater temperature to 160 degrees Fahrenheit (71 degrees Celsius) for several hours. This will destroy the sulfur bacteria. Flushing to remove the dead bacteria after treatment should control the odor problem.

Can I put hydrogen peroxide in my water tank?

The easiest and most cost-effective way to sanitize a water heater is by adding hydrogen peroxide to the tank itself. Let it sit for at least 3 hours, and flush it out prior to using the water for your normal household activities.

Does hydrogen peroxide remove sulfur from water?

Hydrogen peroxide: Hydrogen peroxide system completely removes manganese, iron, and sulfur in well water, making it one of the most effective sulfur eradication systems. Hydrogen peroxide is made up of hydrogen and oxygen, and cannot be considered as a hazardous chemical.Jul 19, 2020

Do you need to dilute hydrogen peroxide for cleaning?

While hydrogen peroxide can be used to clean so many things, it's best to only mix it with water. Combining the solution with ammonia, chlorine bleach, or vinegar in a closed container can cause unsafe gasses to form.Jun 26, 2019

Do you dilute hydrogen peroxide for disinfecting?

It is available as a 7.5% accelerated hydrogen peroxide concentrate that must be diluted with water to a concentration of 0.05% for use. At a concentration of 0.05% a minimum dwell time of 5 minutes is needed to kill the coronavirus.Apr 17, 2020

What is 50% hydrogen peroxide used for?

Hydrogen peroxide is a mild antiseptic used on the skin to prevent infection of minor cuts, scrapes, and burns. It may also be used as a mouth rinse to help remove mucus or to relieve minor mouth irritation (such as due to canker/cold sores, gingivitis).

What is hydrogen peroxide?

Hydrogen peroxide oxidizes hydrogen sulfide to elemental sulfur or sulfate. It can also provide residual hydrogen peroxide to a system. The residual hydrogen peroxide decomposes into dissolved oxygen, helping maintain an aerobic environment and preventing the formation of sulfide.

Is hydrogen peroxide safe to use?

It’s cost effective and has specific targets while forming no toxic by-products. It’s safe to control when handled properly. Hydrogen peroxide has a low freezing point, unlimited solubility in water and it reacts very quickly. It can be used as a biocide for SRBs and iron bacteria and a dechlorinator.

Is chlorine good for ponds?

Some of them are outlined here. Practitioners and professionals in well and pond restoration, well water conditioning, and public water supply management have typically relied on the oxygenating effects of chlorine to manage bacteria and keep water safe for human and animal consumption. Chlorine has been a highly effective ...

Is chlorine a disinfectant?

Chlorine has been a highly effective and inexpensive disinfecting agent used extensively in the United States to treat municipal and individual water supplies. It has played a key role in eradicating waterborne-infectious diseases such as typhoid and cholera.

How is hydrogen sulfide produced?

In both home and municipal collection and treatment systems, hydrogen sulfide is produced via the reduction of sulfates by bacteria under anaerobic conditions. In the presence of aerobic bacteria, hydrogen sulfide forms sulfuric acid, which corrodes metals and concrete.

What is the sulfur analog of alcohol?

Mercaptants or thiols are the sulfur analogs of alcohols containing the –SH (sulfhydryl) group. They react with hydrogen peroxide in alkaline conditions to form disulfides: 2RSH + H 2 0 2 = RSSR + 2H 2 0,—where “R” is a generic designation for any organic compound.

Why is iron removed from water?

The removal of iron from potable water sources is aesthetically advantageous since iron can discolor the water, spot laundry and stain plumbing fixtures. In addition, the growth of iron-oxidizing bacteria can result in abnormal taste and odor as well as contribute to biofouling in water distribution systems.

Is hydrogen sulfide a by product?

Hydrogen Sulfide is a by product of iron bacteria extracting energy from the iron. In the example above – pouring 4 gallons of 35% Food Grade Hydrogen Peroxide into the well in my personal opinion would be, although aggressive, an acceptable amount. Keep in mind I would by-pass all filtration systems and water softeners.

What is hydrogen sulfide?

Hydrogen Sulfide is a by product of iron bacteria extracting energy from the iron. In the example above – pouring 4 gallons of 35% Food Grade Hydrogen Peroxide into the well in my personal opinion would be, although aggressive, an acceptable amount.

Why is hydrogen peroxide used in water?

It sterilizes the water, and it does this without chlorine, which is a great thing, because hydrogen peroxide is nothing but H2O2. It’s like a water molecule with an extra oxygen atom tacked on, and that makes it highly oxidizing and that kills all kinds of microbes, so that’s one reason for hydrogen peroxide.

What is hydrogen peroxide injection?

Updated on July 8th, 2021. Got bacteria or odours in your household water? A hydrogen peroxide injection system offers two benefits for home water well systems. First, it sterilizes water by killing microbes and it does this without chlorine.

Does hydrogen peroxide kill microbes?

A hydrogen peroxide injection system offers two benefits for home water well systems. First, it sterilizes water by killing microbes and it does this without chlorine. Second, hydrogen peroxide does an amazing job getting rid of odours when combined with a whole-house carbon filter. A carbon filter alone can’t do the job.

Is hydrogen peroxide corrosive?

It starts with this drum of 35% hydrogen peroxide. Now that’s pretty corrosive. If you were to touch that, you’d get a burn on your skin. So, it’s something to take seriously, but when it’s added to drinking water, to household water in small quantities, it does two important things.

Can you use hydrogen peroxide in place of chlorine?

These are very dangerous but can be removed with the proper filtration. I recommend using hydrogen peroxide in place of chlorine . Both are oxidants. Hydrogen peroxide does not last as long in the well.

Is hydrogen peroxide a hazardous substance?

It dissipates, converting to water and oxygen. Thus, you may have to repeat the treatment more often, but the byproducts are not hazardous.

How to disinfect a well with bleach?

Pour the required amount of bleach into the well. SEE TABLE BELOW. Run ALL faucets in the house , one at a time , until you smell the chlorine at the faucet. This ensures that the whole system will be disinfected.

How long does it take for water to run to waste?

Forty-eight hours in optimal. Run the water to waste but NOT IN THE SEPTIC SYSTEM for several hours, or until the chlorine taste is dilute enough to be unobjectionable. The best way to run the water to waste is to use the garden hose mentioned above (item 3).

How long does it take to chlorinate a well?

For a typical well, this may take 3-4 hours. NOTE: To avoid pump overheating and possible damage, turn off the water when flow is at a trickle and wait at least 15 minutes before turning on the pump again. After a week of use, retest for bacteria. In some cases, one chlorination treatment WILL NOT be sufficient.

Can iron cause rust in water?

There's nothing I can do about that. If you have iron in your water or iron pipes this method may cause rusty water. Some people recommend the use of calcium hypochlorite granules to provide slow release of chlorine in a well to control bacteria, iron, or hydrogen sulfide odors.

Why is my water rusty?

If you have iron in your water or iron pipes this method may cause rusty water. Some people recommend the use of calcium hypochlorite granules to provide slow release of chlorine in a well to control bacteria, iron, or hydrogen sulfide odors. This will also provide a constant source of carcinogens.

Introduction

Safety

Background

Health

Prevention

Reactions

Chemistry

Use

Carrying the reaction to sulfuric acid using a peroxide to pollutant molar ratio of 5:1 is generally enough to control odors. The reaction proceeds best with a copper or iron catalyst in the presence of a chelating agent such as EDTA. The chelating agent helps prevent the catalyst from coming out of solution and increases the pH range over which th...